This is historical information of device classes implemented in HVisegEHS80 device server.

Use this link to find the valid information.

Development status: Released
Information status: New

Contact:


Class Description

Class for HV Power Supply EHS 80 vvx from iseg

Families: PowerSupply

Key words:

Platform: All Platforms

Language: Cpp

License:

Contact:

Hardware

Manufacturer: iseg

Product:

EHS80

Bus: Not Applicable

Class interface

Attributes:

Name Description
ChannelStatusScalar: DevDouble Off (0), On (1), resetEmergencyOff (2), setEmergencyOff (3), clearEvents (10)\n\nRead: An enumerated value which shows the current state of\n the output channel.\n Write: Change the state of the channel.\n If the channel is On, and the write value is Off, then the channel\n will switch Off.\n If the channel is Off, and the write value is On, and if no other\n signals (mainInhibit, outputInhibit, outputEmergencyOff or outputFailureMaxCurrent)\n are active, then the channel will switch on.\n \n If the write value is resetEmergencyOff, then the channel will \n leave the state EmergencyOff. A write of clearEvents is necessary\n before the voltage can ramp up again.\n If the write value is setEmergencyOff, then the channel will have \n the state EmergencyOff, which means that the High Voltage will \n switch off without a ramp and reset of the outputVoltage to null volt.\n \n If the write value is clearEvents, then all failure messages \n of the outputStatus will be reset (all channel events, all module events\n and the state emergencyOff).
MeasTerminalVoltageScalar: DevDouble The measured voltage at the output terminals.
MeasSenseVoltageScalar: DevDouble The measured voltage at the sense input lines.
SetCurrentScalar: DevDouble The current limit of the channel.
MeasCurrentScalar: DevDouble The measured output current.
RampSpeedScalar: DevDouble Voltage Rise Slew Rate [V/s].\n\nThe slew rate of the output voltage if it increases\n\n(after switch on or if the Voltage has been changed.
ChannelStatusStrScalar: DevString —
SetVoltageScalar: DevDouble The nominal output voltage of the channel.
CrateSlotScalar: DevLong Crate Slot (from 1 to 4)
ChannelNumberScalar: DevLong Channel Number (from 1 to 16)
RampSpeedDownScalar: DevDouble Voltage Fall Slew Rate [V/s].\n
ResistanceScalar: DevDouble MeasSenseVoltage/MeasCurrent

Commands:

Name Description
StateInput: DevVoid
Output: State
State Code		 This command gets the device state (stored in its <i>device_state</i> data member) and returns it to the caller.
StatusInput: DevVoid
Output: ConstDevString
Status description		 This command gets the device status (stored in its <i>device_status</i> data member) and returns it to the caller.
SafetyLoopResetInput: DevVoid
Output: DevVoid		 Reset module after Safetyloop error.

Pipes:

Name Description

Properties:

Name Description
ChannelNbDevLong Channel Number (from 1 to 16)
CrateSlotDevLong Crate Slot (from 1 to 4)
HVisegMPODCtrlDeviceDevString Name of the HVisegMPODCtrl device making the Ethernet connection.
SimulationModeDevULong 0 -> real mode, 1 -> simulation mode

7 Aug 2021, DS Admin
Updated:
The device class has been updated.
You can see previous version here .


21 Jul 2018, DS Admin
Updated:
The device class has been updated.
You can see previous version here .


7 Jul 2018, DS Admin
Updated:
The device class has been updated.
You can see previous version here .


23 Feb 2017, Piotr Goryl
Updated:
The device class has been updated.
You can see previous version here .


19 Jan 2017, Piotr Goryl
Updated:
The device server has been updated.
You are looking at this version now.


3 Jan 2017, Piotr Goryl
Created:
The device server has been added to catalogue.
Added by:pgoryl2 on:19 Jan 2017, 10:51 a.m.